Directv Card
box will be displayed once your manual calibration setting has been stored. Click "OK" 9) Remove the serial cable (and power supply if you need to)
10) Connect the power supply, insert your HU card into the Avenger SE card slot (microchip facing upwards) and allow 1 minute for Initial Calibration to complete.
11) Insert the Avenger SE emulation board into your receiver, and check the status of the Green Calibration LED: 12) Check the status of the Green Calibration LED:
(a) If the green Calibration LED indicator flashes ON slowly (approximately 6 seconds between each flash) and video is restored, you have successfully calibrated
the unit. (b) If the green Calibration LED indicator flashes OFF slowly (approximately 6 seconds between each flash) and video remains intermittent after 1 minute:
- remove the Emulation board from your receiver. - Reconnect the Serial cable to your PC COM port. - repeat from step 6), incrementing the calibration
setting in step 7) by 1. (i.e. Set the spending limit to “2” on your receiver). (c) If the green Calibration LED indicator remains lit and there is no video;
repeat from step 6), incrementing the calibration setting in step 7) by 1. (I.e. Set the spending limit to “2” on your receiver). In order to return the unit to auto
calibration mode Refer to section "5.1 Resetting your Avenger SE to Factory Defaults" to RESET your Avenger SE unit OR: 1) Follow steps 1 to 6 of
section "4.3 Manual Calibration using a PC and Calibration software (and Serial Cable provided)". 2) Select click "Auto" in the "Calibration Selection" Section.
3) A confirmation dialog box will be displayed once Auto Calibration has been stored. Click "OK" NOTE: If your card does not have DSW 0600 it may
take up to 30 minutes for your card to update (refer to Procedure 3.3 step 5). In this case the Green Calibration LED will not be lit (or will flash ON every
3 to 6 seconds) but you will not have video until your card updates to DSW 0600. 4.4 Auto Calibration with Loader/Unlooper and Calibration software
[Prefered if you own a Loader Unlooper] The auto calibration procedure using a Loader/Unlooper requires minimal user input and should be adequate
for most users. Using this method, calibration can be completed in a matter of minutes, whereas "4.1 Auto Calibration in Receiver" can take up to 30 minutes.
from the factory (ie brand new, or "virgin") is activated for programming by DirecTV, the card writes down the receiver’s identification number into its
NOTE: The Avenger SE calibration software will automatically reset the Avenger SE to factory defaults before applying any setting you have selected using
the procedures in Section 4.0, so in that case this RESET procedure is not necessary. 5.2 Calibration problems The 4 most common calibration problems arise
from the following: 1) Your HU Card has had its code modified and you are experiencing "Hashing" as a result. This can be corrected by following
procedure "3.3 Clean your HU Card (Required Loader)" and repeating one of the calibration steps in section "4.0 Initial Calibration Procedure".
2) You have calibrated another HU Card on the same unit and the previous settings are now stored. This can be corrected by following procedure
"5.1 Resetting your Avenger SE to Factory Defaults" and repeating one of the calibration steps in section "4.0 Initial Calibration Procedure" for your new card.
3) Your card has not been updated to USW 0800 and DSW 0600 (the latest revision of card software). This can be corrected by following procedure
"3.3 Clean your HU Card (Required Loader)" and repeating one of the calibration steps in section "4.0 Initial Calibration Procedure".
4) You did not insert the Avenger SE into your receiver while the receiver was on a channel you do not usually get with your card/sub.
It is VITAL that you turn to a channel you cannot usually receiver (a good channel to use is a PPV channel for an event you have not purchased).
This can be corrected by following procedure "5.1 Resetting your Avenger SE to Factory Defaults" and repeating one of the calibration steps in section
then computes the datastream, and if the card says the channel is authorized, it descrambles the signal for the television. Programmer An ISO7816
smartcard reader/writer that plugs into your computer’s serial port and permits a hacker to read and write to any ISO7816 smartcard, such as the access cards.
Update (aka USW) A change in the code on the access card, usually done to destroy cards with hacks on them, or to add some fuctionality
(such as interactive TV) to the access card. USW stands for Update Status Word, and simply counts the number of times the card has been
updated. A card with a USW of 5 has been updated 5 times, for example. H-Cards requirement shops shopping adding pay companys tv_usa
hucard Directv CardLoaders Unloopers CardLoader DirectTVHU CardUnloopers DirectTVHUCard Loaders huUnloopers Directloaders TVHU CardLooders
Unlopers directtvloaders directloaders online cheap cheapest best now dealers hack hackers H-Cards do not currently get updated anymore...code changes
are done through something that is a little different, called a dynamic update.For a more detailed explanation of a dynamic update, see "Dynamic Update"
below in this dictionary. hackcom hackerscom directtvhack directtvhackers descramblerscom directhack dishhackers dishtvhackers cardhackers cardhacker
dsshack dssdescramblers unlooperscom loaderscom wwwloopers wwwloaders wwwloaderscom hackdss dssunloopers dssloaders cheap cheapest best sales
Directv Card