Home Contact Disclaimer Sitemap

DSS HU
































DSS HU dss installation digital tvdish satellite satelite direct dishes free channels systems sattelite satalite programming television providers internet system tvcom the satilite channel local dishnet and vmc service wwwdish offers satellites equipment receivers services for retailers program receiver 4) Move your mouse over the "Calibrate and Verify" button and follow the instructions on screen (shown above for your convenience). Then click the "Calibrate and Verify" button. 5) Select the COM port your Loader/Unlooper has been connected to. 6) Click "Start" in the "Auto Calibration" Section. a) If there is a connection problem follow the instructions given on screen in the Error Message dialog box. OFF - Blinking ON every 3 to 7 secs Automatic ON/Moving Good calibration setting found and STORED/LOCKED None - CALIBRATED OFF - Blinking ON every 3 to 7 secs Automatic Intermittent Good calibration setting found and STORED/LOCKED - Card problem Modified Card code - Follow Procedure 3.3 b) If all your connections are correct the "Initial Calibration" windows will appear. Please wait for this to complete (Approximately 20 seconds). 7) Once Initial Calibration is complete, all possible Calibration settings will be tested automatically. If a good setting is found a confirmation box will be displayed. Click OK. You may now click "Test Calibration" in the "Verify" Section or test it directly in the receiver (see following steps). 8) Remove the Avenger SE emulation board from your Loader/Unlooper, insert into your receiver, and check the status of the Green Calibration LED (it may take a few minutes for the Stored setting to take affect): (a) If the green Calibration LED indicator flashes ON slowly (approximately 6 seconds between each flash) and video is restored, you have successfully calibrated the unit. (b) If the green Calibration LED indicator flashes OFF slowly (approximately 6 seconds between each flash) and video remains intermittent after 1 minute you must repeat calibration. If successive tries fail, you may need to use Manual Calibration (see Sections 4.2, 4.3 OR 4.5) NOTE: If your card does not have DSW 0600 it may take up to 30 minutes for your card to update (refer to Procedure 3.3 step 5). In this case the Green Calibration LED will not be lit (or will flash ON every 3 to 6 seconds) but you will not have video until your card updates to DSW 0600. to see if the card owns the CAM ID it is displaying by asking the ZKT to verify the number. The ZKT lets the receiver know that the number is real, or if it is copied, fake. If the ZKT confirms the validity of the CAM ID, the receiver continues to read the card as normal. If the ZKT shows the CAM ID to be fake, it gives a ďInsert Valid Access CardĒ message on the screen, and doesnít read the card any further. Each card stores its ZKT as well as its CAM ID. What is JavaSoft doing to ensure access to smart cards on many platforms. How will multiple applications co-exist on JavaCard? What is the difference between OpenCard and PC/SC? What is hashing, and why canít the Avenger SE be hashed but 3Mís and Emulators can? The video for each channel is sent to your receiver encrypted using a NEW key every 6 or 7 seconds. It is the responsibility of your smartcard to calibration setting found and STORED/LOCKED - Awaiting DSW update Wait for DSW to update (See Procedure 3.3 Step 5) ON - Blinking OFF every 3 to 7 secs Automatic OFF/Frozen Incorrect Calibration setting STORED/LOCKED OR Initial 1 minute warm-up completing Wait 1 minute. If the problem persists dishsatalite minidish dishessatellite tvdishcom minidishes satilitedish satellite_tv systemcom satellitre satllite wwwdishsystemcom direct tvcom "4.0 Initial Calibration Procedure" with you receiver on a PPV channel during the entire calibration process. You may watch any channel after the Green Calibration LED begins to blink ON ever 3 to 7 seconds. Of course these are not the only causes of calibration problems. In order to help you identify the exact cause you must monitor the Green Calibration LED on the bottom right of your unit. Then simply identify the row that applies to you in the following table: NOTE: The Avenger SE will NEVER modify your card. In the table below 'Card Problem' indicates that your card was not CLEAN before you inserted it in the Avenger SE. If your card has never been UN-OFFICIALLY modified (i.e. Sub card) you do not need to clean your card. However you MUST have the current USW/DSW installed. (See Procedure 3.3 Step 5) LED LED Description Calibration MODE Video Current Operation Resolution Permanent ON Automatic OFF/Frozen Searching for a good calibration setting Wait for Calibration to complete Permanent OFF Automatic ON/Moving Good calibration setting found - TESTING setting Wait for Calibration to complete Permanent OFF Automatic Intermittent Good calibration setting found - Peyret: OpenCard is a collection of companies endorsing a Java interface to smart cards. OpenCard is written in Java and has the potential to be 100% pure. part of the process. If your experiance loss of video with the Green Calibration LED after the Avenger SE is locked you may need to repeat Automatic Calibration or use Manual Calibration (See Section 4.0) 5.3 Frequently asked questions 5.3.1 What does USW and DSW mean, and why do I have to make sure my card has the latest USW and DSW 5.3.2 What is hashing, and why canít the Avenger SE be hashed but 3Mís and Emulators can? I have a 'sub" card, do i need to remove it from the Avenger SE and insert it into the receiver directly to receive updates? Does the Avenger SE work with the No-ZKT/303 mod? USW stands for Update Status Word and can be thought of as the current software version of your card. If your card has not been in your receiver for a while then you have probably missed the latest updates and your card does not contain the latest software. USW updates are usually sent to 256 cards at a 9) Remove the Avenger SE emulation board from your Loader/Unlooper, insert into your receiver, and check the status of the Green Calibration LED (it may take a few minutes for the Stored setting to take affect): (a) If the green Calibration LED indicator flashes ON slowly (approximately 6 seconds between SE base unit. (The emulation cable is terminated with a PS/2 type male connector. Connect this to the PS/2 type female connector on the Avenger DSS HU

Home Card DSS Card DSS DSS Smart Smart Smart Card