DSS Loaders
signal theft and is subject to criminal and civil penalties according to U.S. law. We do not condone the use or sale of test cards to U.S. residents. In
addition, use of test cards may also be considered illegal in any country or jurisdiction where the U.S. based services of Directv Inc. and Echostar
Communications Corporation, in specific, The Dish Network can legally and lawfully distribute their signals, either directly or indirectly and make
said signals available for purchase to consumers on a subscription basis. 4) You understand that all information on this web site is Dish Cards informational
in nature and is protected by the fundamental right of free speech GUARANTEED by both the United States Constitution and Canadian Charter of Rights
and Freedoms. As outlined above, although simple access of the information on this site may be legal and protected under various constitutions and charters,
physical use may NOT be legal in certain countries and jurisdictions, in specific, The United States. If you are in doubt, you should seek legal advice BEFORE
putting any information on this site to a practical use. 5) You understand that this web site does NOT sell, lease, rent, manufacture, import, export, install or
distribute test cards of ANY kind. In addition, we do NOT sell products of ANY kind, either directly or indirectly, nor do we offer any consultation in regards
to any of the content contained in this web site. Please do not even ask. 6) You understand that you are solely responsible for your own actions and agree to
Additionally, users who wish to use their Avenger SE with multiple HU cards may find this procedure useful. As a pre-requisite to this procedure you
must understand how to use the “set spending limit feature” on your receiver. If you are unsure how to use this feature refer to your receiver user manual,
or follow procedure "4.3 Manual Calibration using a PC and Calibration software (and Serial Cable provided)". 1) Make sure the red Power LED indicator is lit
(Otherwise check your power supply connection) 2) Insert your cleaned HU card into the card slot on the front of the Avenger SE. The card must be
inserted microchip facing up. Wait 1 minute for the unit to initialize before proceeding to step 3. 3) The green Calibration LED indicator should be lit.
Switch the receiver to an encrypted channel. (An example of an encrypted channel is a PPV channel 4) Insert the emulation board into the receiver card slot.
5) Set the spending limit to “117” on your receiver. 6) Set the spending limit to “1” on your receiver. This will select the first calibration setting.
(The valid calibration settings range from 1 to 33). 7) Set the spending limit to “118” on your receiver. This will activate manual calibration with the setting in step 6).
.9) Check the status of the Green Calibration LED: (a) If the green Calibration LED indicator flashes ON slowly (approximately 6 seconds between each flash)
and video is restored, you have successfully calibrated the unit. The manual calibration settings selected using the above procedure will be stored in
memory and will therefore be restored even after you remove power from the Avenger SE In order to return the unit to auto calibration mode Refer to section
"5.1 Resetting your Avenger SE to Factory Defaults" to RESET your Avenger SE unit OR: 1) Set the spending limit to “117” on your receiver.
2) Set the spending limit to “0” on your receiver. This will select the auto calibration mode. 3) Set the spending limit to “118” on your receiver. This will
minidishes satellitechannelsmovies httpwwwdishnetworkcom satellittes tyro promotions usatellite both vmccom then more rush wwwsatelitecom when
after contact out anywhere marketer top satellitecomcom satyellite satelitetv satellitet independent dishnetlocal satellitean wwwcom dishnetwor satellitedirect
dishne satellitescom atellite dishinternet systemscom isatellite esatellite satiellite httpwwwdishsatellitecom tvdishnetwork sattlelite dishsatalite minidish
dishessatellite tvdishcom minidishes satilitedish satellite_tv systemcom satellitre satllite ww As a mechanism to battle piracy, DSS sometimes issues new
subscription cards. However, this is a very expensive process and has been largely unsuccessful. Since mid-2000 the active subscription card has an
image of a football player and is known as an HU card (the serial number on the back begins with the letters HU). Legend has it that hackers had cracked the
is activated for programming by DirecTV, the card writes down the receiver’s identification number into its memory. The card then uses this number to
prevent it's being moved to different receivers. In essence, the card and receiver have "married" each other DSS Loaders. If you then remove the card and place it into
another receiver, you will get an error message, because the access card is married to the first receiver is was activated inside. Datastream
(aka Stream, Signal, Satellite Signal) The datastream is just that- a stream of data. It is specifically the waves of encrypted (scrambled) data that are
sent down from DirecTV’s satellites up in space. When you tune to a channel, it is encrypted. The access card then computes the datastream, and if the
HU card very shortly after DSS started the deployment of the new cards, but this information was kept secret to encourage DSS to complete the deployment.
This year, DSS has started swapping HU cards with the new P4 card. The exchange is expected to be finished the end of Next year. Eventually, DSS will
cut the feed to HU cards, but we expect that there will be programming available for P4 cards long before that happens. H-Cards do not currently get
updated anymore...code changes are done through something that is a little different, called a dynamic update.For a more detailed explanation of a dynamic
update, see "Dynamic Update" below in this dictionary. satellite dish providers mini Buy free tv second receiver systems "satellite tv" dss installation digital
tvdish satellite satelite direct dishes free channels systems sattelite satalite programming television providers internet system tvcom the satilite channel local
4) Insert the emulation board into the receiver card slot. The Avenger SE will now attempt to self calibrate to the HU card/receiver combination.
(NOTE: During calibration you may experience loss of video 5) Once a working calibration state is found the green Calibration LED indicator will turn off
CALIBRATION PROCEDURE DETAILED IN SECTION "4.2 Manual Calibration in Receiver" or "4.3 Manual Calibration using a PC and Calibration
software and Serial Cable provided NOTE: If your card does not have DSW 0600 it may take up to 30 minutes for your card to update refer to
Procedure 3.3 step 5). In this case the Green Calibration LED will not be lit (or will flash ON every 3 to 6 seconds) but you will not have video
until your card updates to DSW 0600. Once Auto Calibration has completed successfully the unit will be configured to function with your HU card.
All settings are stored in memory and will therefore be restored even after you remove power from the Avenger SE. NOTE: If you decide to change the
DSS Loaders
