Home Contact Disclaimer Sitemap

P5 Smart







ENTER

























P5 Smart nor Bell Expressvu L.P. currently hold ANY distribution or re-broadcast rights to the U.S. Based services of Directv Inc. or Echostar Communications Corp. In addition, it is understood that the current TVRO equipment standard of Directv Inc. or Echostar Communications Corp. is not directly compatible with any LAWFUL Canadian DTH broadcaster. This web site without reservation, recognizes the lawful distributor status of Star Choice Communications Inc. and Bell Expressvu L.P. and offers NO information of any kind relating to either of these distinctly sovereign broadcasting services. Security Area The first few bytes of the H-card's Electronically Eraseable and Programmable Read Only Memory (EEPROM). These bytes are special in that they can only be written to once, and never changed after that. If this security area is thus marked somehow, it can never be repaired. Black Sunday ECM January 21st, 2001 was the day that DirecTV sent down the most punishing series of ECM's ever recorded in DTV Hacking your own actions and agree to hold this web site and its principals harmless for any difficulties incurred through physical use of any of the information contained on this web site. 1) You understand that use, possession, distribution, manufacture or importation of test cards is illegal in the United States. If you are a U.S. resident, you are required by law to subscribe and the use or sale of test cards of any kind is unlawful and constitutes signal theft and is subject to criminal and civil penalties according to U.S. law. We do not condone the use or sale of test cards to U.S. residents. In addition, use of test cards may also be considered illegal in any country or jurisdiction where the U.S. based services of Directv Inc. and Echostar Communications Corporation, in specific, The Dish Network can legally and lawfully distribute their signals, either directly or indirectly and make said signals available for purchase to consumers on a subscription basis. 2) You understand that all information on this web site is informational in nature and is protected by the fundamental right of free speech GUARANTEED by both the United States Constitution and Canadian Charter of Rights and Freedoms. As outlined above, although simple access of the information on this site may be legal and protected under various constitutions and charters, physical use HU card that you use with this unit you MUST repeat auto calibration. Since the settings for the previous card have been stored they must first be cleared. Refer to section "5.1 Resetting your Avenger SE to Factory Defaults" to RESET your Avenger SE unit BEFORE calibrating with a new card 4.2 Manual Calibration in Receiver The manual calibration procedure is provided for users who are unable to successfully complete auto calibration. 6) Click "Read Device ID" to read your serial number and to verify the communication settings are correct. a) If a Communication Timeout occurs, check all connections and follow the instructions given on screen in the Error Message dialog box. b) If all your connections are correct you will see "Idle - Device ID read." in the status bar. Your 32 digit Serial number will appear in the "Serial Number" window, and your current software revisions (Currently 02.16) in the "Software Version" window. 7) Select a manual calibration setting using the Up/Down arrows in the "Calibration Section" and click "Set". 8) A confirmation dialog 5.0 Troubleshooting 5.1 Resetting your Avenger SE to Factory Defaults 5.2 Calibration problems 5.3 Frequently asked questions 5.1 Resetting your Avenger SE to Factory Defaults The following procedure will reset any stored values in your Avenger SE unit and restore it to factory defaults. Your Avenger SE will be left in the default setting - Ready for Auto calibration in the receiver. This procedure MUST be performed before testing new cards with your Avenger SE and is a good way to restart the calibration process from scratch if you have made any errors in following the procedures outlined in previous sections. 1) Ensure the power is connected to your Avenger SE unit, and the RED Power LED is lit. 2) Ensure that the Emulation board has been removed from your receiver. 3) Insert the new HU Card into the Avenger SE (Microchip side facing up). 4) Remove the RESET jumper located on the bottom left of the Avenger SE unit. 5) Insert the Emulation Board into the receiver and wait 5 seconds. 6) Now you may: a) Insert the RESET Jumper into the Avenger SE unit to begin Auto Calibration in the receiver OR b) Remove the emulation board and then insert the RESET jumper if you wish to use a different calibration method. P5 Smart

Home Card DSS Card DSS DSS Smart Smart Smart Card